| products |
|
Rubidium Series 1 & 3:
Module SL |
|
|
|
Leaflet:
pdf-file.... zip- file Manual: pdf-file.... zip- file |
|
||||||||||
| FEATURES |
• Switcher for LTC signals
• Signal monitor with status indicator • GPI outputs for error indication • Optional SNMP and status indication via an internet browser • Bi-stable signal outputs relays |
|
RUBIDIUM Series 1 & 3, Module SL: |
|
The Alpermann+Velte Rubidium "SL" module is an automatic switchover unit for LTC signals. It analyzes and monitors two LTC sources. If a LTC source is lost, the LTC output is automatically switched to the other error free source. Connected with a reference time source, the LTC signal is monitored and analyzed in conjunction with this reference time. The module offers a monitor function for errors in the LTC, errors in the reference time source, for time differences between the two individual LTC sources and for the status information of all input sources. If an Ethernet module is present in the system, the status and error messages can be queried via a browser or SNMP. When a "SL" module is combined with two of our master generators RUB "GT" or RUB "GL", a fully redundant fail-safe LTC generator system is possible. One or both LTC input sources can also be acquired from external non Alpermann+Velte devices as long as the LTC signal complies with the SMPTE/ EBU format rules. |
|
|
In the event of a failure the signals can be switched automatically or manually. The
changeover is completed with bistable relays. The relay contact remains in its last
position if power is lost. The relays are mounted on a separately installed circuit
board, so that even when physically exchanging a module the signal flow can
continue without interruption.
|
|
|
LEDs located on the front of the module indicate the operating status and the built-in GPIs can be programmed to signal errors or other pre-programmed warnings. The backlit keys on the front of the module can be programmed to suit the user specific needs (e.g. a key could be programmed to manually switch incoming sources). |
SL Front View |
|
Also available are distribution amplifiers modules with four separate outputs or six fail-safe amplified outputs specifically designed for redundant systems. The Rubidium series also includes various generators for other signals (VITC, DVITC and ATC) as well as inserters and converters for all these before mentioned signals. |
|
|
All programmable functions and the communication between modules are setup with the included configuration software. The operating status of the module is available at any time via a status monitor function. The status request is made using a PC software via the USB interface of the applicable housing (H1, H3, S1, T1). The firmware or additionally purchased options are setup via this same USB interface (a USB port is included with all models). If the system includes an Ethernet module (RUB IE), a standard web browser can then additionally access the status information and the configuration menus of the "SL"-module. Monitoring via SNMP is then also possible. |
Browser Configuration |
Rubidium Configuration |
Rear Panels Rubidium 1 (left) & 3 (right)
|
|
SL SPECIFICATIONS
| LTC/MTD IN (2xRJ45) |
| RS485 |
| Balanced in- or outputs of a RS485 serial interface |
| Format |
| ANSI/SMPTE 12M-1999, balanced |
| Signal Level |
| 100 mVp-p to 5 Vp-p, auto-ranging |
| Input Impedance |
| 18 kΩ |
| Frequency |
| 19 - 33 Frames per second |
| SERIAL IN |
| Serial time and date string |
| TELEGRAM IN |
| Impulse telegram |
|
LTC/MTD OUT (RJ45 and DSUB9F) |
| RS485 |
| RS485 serial interface, hard-wired with signals at LTC/MTD IN |
| LTC OUT |
| Balanced LTC output, switched via relay to one input |
| SERIAL OUT |
| Serial time and data string, switched via relay to one input |
| TELEGRAM OUT |
| Impulse telegram, switched via relay to one input |
|
REF IN (RJ45) |
| PPS IN |
| Pulse per second, input |
| RXD IN |
| Reference time and date input, serial data string |
|
REF OUT (2 x RJ45) |
| PPS OUT |
| Pulse per second output, hard-wired with signal at REF IN |
| TXD OUT |
| Reference time and date output, hard-wired with signal at REF IN |
|
GPI OUT (RJ45) |
| FAIL |
| Failure Signals |
| WARNING |
| Warning Signals |
|
Others |
| Operating Voltage |
| 12 - 30 VDC |
| Power consumption |
| max 1.2 W |
| Weight |
| 0.3 kg approx. |
| Dimensions Rub H1 |
|
2 circuit board (W x D): 100 x 160 mm / 3.94 x 6.30 inch Rear panel: 103 x 44 mm / 4.06 x 1.73 inch |
| Dimensions Rub H3 |
| Rear panel: 3RU, 8HP |
| Environmental characteristics, operating |
|
Temperature: +5 °C - +40 °C Relative humidity: 30 % - 85 %, non-condensing |
| Environmental characteristics, non-operating |
|
Temperature: -10 °C - +60 °C Relative humidity: 5 % - 95 %, non-condensing |
|
Product ordering ID SL modules |
| RUB1 SL |
| LTC/RS485 changeover unit and monitoring module (1RU) |
| RUB3 SL |
| LTC/RS485 changeover unit and monitoring module (3RU) |
The RUBIDIUM modules must be used in conjunction with a RUBIDIUM housing and a RUBIDIUM power supply, please see our overview leaflet for more information.
We reserve the right to modify specifications without notice.
© Alpermann+Velte 1996 - 2008; October 27, 2008